Concrete Systems NV | Catalog | 1. Aluminium bekisting | 1.4. Toebehoren
Construx - Concrete Systems Construx - Concrete Systems Construx - Concrete Systems Construx - Concrete Systems Construx - Concrete Systems Construx - Concrete Systems

1. Aluminium shuttering- 1.4. Accessories


The accessories used for assembling the CONALU formwork can be found below. These accessories are offered for sale as for renting. Do not hesitate to contact us if you would like more information concerning the price and function of these accessories.


Column adjuster nut

The column adjuster nut is used for creating corner compositions and perpendicular columns.

 

More information? Click here

Pivot + locking clip

Used to connect the prop on the horizontal brace connector and/or the standard brace connector.

In some cases it can be used instead of a push & pull prop brace.

More information? Click here

Horizontal brace connector cpl

Used for double props to attach the lower pipe on the lower part of the formwork, on top a brace connector is used.

If the panel is laying down on its longest side you can't use a brace connector. Then it's recommended to use a horizontal brace connector.

1 x Pivot + locking clip - galvanized - included

More information? Click here

Brace connector cpl

1 for every prop to attach it onto the formwork panel, through one of the many brace connector holes supplied in the filler pieces of the frame

2 x Pivot + locking clip - galvanized - included

More information? Click here

Pression plate

Mainly used for composing columns ( traditional and winged ), corner compositions and twisted boards with extra holes placed on their longest side.

More information? Click here

Tie rod coupler

Used to attach compensation rails on our panels in combination with wing nut brackets.

More information? Click here

Raised tie holder

The raised tie holder is used with panels which are placed on their side. If the height of the formwork panel is around the similar height of the wall then you'd see the PVC pipes on the edge of the concrete wall when using the standard tie holes. Using raised tie holder you can anchor above the panel.

More information? Click here

Attachment wedge cpl

Exists out of a T-piece, cotter and a blank.

Used to attach bracket's, compensation tubes and horizontal brace connectors to the formwork.

More information? Click here

Base coupler

Used when the formwork needs extra coupling.

When using single push & pull props it's obliged to place a base coupler for every prop placed to take hold of the upward pressure on the panel.

More information? Click here

Bracket

Maximum load : 400 kg

Has to be attached with 2 attachment wedges.

Weight Aluminium : 5,85 kg

Weight Steel : 7 kg

More information? Click here

Crane lifthook semi-auto

Easy to handle with one motion of the hand

CE license / Delivered with the necessary certificates

Maximum load : 750 kg

More information? Click here

Hinged compensation tube

Hinged compensation tube with pin ( complete )

75 cm - 100 cm - 125 cm - 150 cm

Hinged compensation tube with hole

50 cm - 75 cm - 100 cm - 125 cm - 150 cm

More information? Click here

Compensation tube

Compensation tubes are available in the following lengths :

50 cm - 60 cm - 75 cm - 100 cm - 125 cm - 150 cm - 175 cm - 250 cm

More information? Click here

Compensation rail

Compensation rails are available in the following lenghts :

50 cm - 75 cm - 100 cm - 125 cm - 150 cm

More information? Click here

Hex coupler

Used to combine two tie rods.

Obtainable for use with a tie rod Ø 15 & tie rod Ø 20.

More information? Click here

Plate washer for hex nut

Always used in combination with a hex nut.

 

 

More information? Click here

Hex nut

Substitute for the combination of the tie rod and wing screw or the combination of the tie rod with the wing nut bracket when it's impossible to use these combinations because of lack of space.

Obtainable for use with a tie rod Ø 15 & tie rod Ø 20.

More information? Click here

Wing nut bracket

Ø 100 mm

Obtainable for use with a tie rod Ø 15 & tie rod Ø 20.

More information? Click here

Combination plate

Ø 140 x 100 mm

Obtainable for use with a tie rod Ø 15 & tie rod Ø 20.

More information? Click here

Hooked anchors

Hooked anchors are used for onesided encasing to anchor the supporting legs in the top slab.

Ø15 mm 450 mm

Ø20 mm 450 mm

More information? Click here

Tie rod Ø 15 mm & Ø 20 mm

These are available in the following size :

0,35 m - 0,75 m - 1,00 m - 1,25 m - 1,50 m - 2,00 m - 2,50 m

Other sizes are available on request.

More information? Click here

Compensation coupler

Used to clutch together two adjacent panels which have a filling piece in between with a maximum size of 15cm.

Also used to compose an exterior corner using a wooden or aluminium cornerprofile.

More information? Click here

Rapid alignment coupler left

Mainly used for composing interior angles instead of a standard rapid alignment coupler.

More information? Click here

Rapid alignment coupler right

Standard rapid alignment coupler

Used to clutch together two adjacent standing panels.

More information? Click here

Rapid alignment coupler CS

Left and right coupler in one piece.

Used to clutch together two side by side standing panels.

More information? Click here